Einhell GC-DW 1000 N Deep well pump 1000W with multi-stage impeller system - EIN-4170955

Expansion and pressure vessels are essential components for effective pressure management in water supply, heating, and other hydraulic systems. They help absorb pressure fluctuations, protecting system components from excessive stress and premature wear. At the same time, they contribute to stable and efficient system operation by reducing sudden pressure variations.

The IMAS IM25-8S-180B is a three-speed hot water circulator pump designed for circulating clean water and liquids that do not contain chemicals. It is suitable for domestic heating and air-conditioning systems operating in pressurized closed or open circuits. The pump features three selectable operating speeds, with power consumption of 90W, 150W and 180W, allowing its performance to be adjusted according to the requirements of the installation. It delivers a maximum flow rate of 4.5 m³/h and a maximum head of 8 m. The pump body is manufactured from brass and incorporates a wet-rotor motor. The motor housing is made of die-cast aluminium, while the impeller is manufactured from technopolymer. The hardened stainless steel motor shaft is supported by graphite bearings and lubricated directly by the pumped liquid. The rotor protective sleeve, stator sleeve and sealing flange are made of stainless steel. The pump also features a ceramic thrust ring, ethylene-propylene sealing rings and a brass air vent plug. Designed for hot-water circulation, the IM25-8S-180B can handle liquid temperatures up to 110°C and a maximum operating pressure of 10 bar. It operates from a single-phase 230V/50Hz power supply and features IP44 protection and Class F insulation. The pump has an installation length of 180 mm, 1½" threaded connections and must be installed with the motor shaft in a horizontal position.

The Einhell GC-DP 5010 G is a robust 500W submersible dirty water pump designed for a wide range of drainage applications. It is suitable for emptying rain barrels, collecting containers, tanks, flooded areas and other locations where dirty water needs to be removed efficiently. With a maximum flow rate of 12,000 L/h (12 m³/h), the pump delivers a maximum head of 8 m and a maximum delivery pressure of 0.8 bar. It can handle foreign particles up to 10 mm, making it suitable for dirty water containing small solid particles. The pump features a durable construction with a cast iron housing section and stainless steel motor housing. A high-quality mechanical seal contributes to reliable operation and long service life. The infinitely height-adjustable float switch provides automatic operation according to the water level. An integrated carrying handle makes the pump easier to transport and position. The GC-DP 5010 G features a 42 mm (G1¼" IG) pressure connection and includes adapters for 38 mm (1½"), 32 mm (1¼") and 25 mm (1") hoses. It comes with a 10 m power cable for flexible installation.

Expansion and pressure vessels are essential components for effective pressure management in water supply, heating, and other hydraulic systems. They help absorb pressure fluctuations, protecting system components from excessive stress and premature wear. At the same time, they contribute to stable and efficient system operation by reducing sudden pressure variations.

The AQUASTRONG EF-01B is a water level float switch designed for the automatic start and stop control of compatible water pumps according to liquid level. It is suitable for water tanks, reservoirs, drainage systems and other applications requiring automatic liquid-level control. The balance block allows the float's operating position and switching range to be adjusted during installation, providing greater flexibility according to the required minimum and maximum water levels. This version comes with a 10 m H07-RN-F cable, making it particularly suitable for installations where a longer cable length is required. AQUASTRONG technical documentation lists 10 m as one of the available cable lengths for the EF-01B, together with electrical ratings of 16(8)A / 250V and 16(14)A / 125V. The EF-01B is designed for a service life of approximately 5,000 operating cycles. Its operating limits allow use with liquids at temperatures up to 35°C and a maximum ambient temperature of 40°C.

High-quality horizontal water tanks with feet designed for safe, reliable, and efficient water storage in residential, commercial, and industrial applications. Their horizontal design and integrated support feet provide enhanced stability and secure floor installation, while the durable construction makes them suitable for domestic water storage, irrigation, and backup water supply systems.

The IMAS IM25-4S-180B is a three-speed hot water circulator pump designed for circulating clean water and liquids that do not contain chemicals. It is suitable for domestic central heating and air-conditioning systems operating in closed or open pressurized circuits. The pump features three selectable operating speeds, with power consumption of 38W, 53W and 72W, allowing its performance to be adjusted according to the requirements of the installation. It delivers a maximum flow rate of 4.0 m³/h and a maximum head of 4 m. The hydraulic pump body is manufactured from brass and incorporates a wet-rotor motor. The motor housing is made of die-cast aluminium, while the impeller is manufactured from technopolymer. The hardened stainless steel motor shaft is supported by graphite bearings and lubricated directly by the pumped liquid. The rotor protective sleeve, stator sleeve and sealing flange are made of stainless steel. The pump also features a ceramic thrust ring, ethylene-propylene sealing rings and a brass air vent plug. Designed for hot-water circulation, the IM25-4S-180B can handle liquid temperatures up to 110°C and a maximum operating pressure of 10 bar. It operates from a single-phase 230V/50Hz power supply and features IP44 protection and Class F insulation. The pump has an installation length of 180 mm, 1½" threaded connections and must be installed with the motor shaft in a horizontal position.

Expansion and pressure vessels are essential components for effective pressure management in water supply, heating, and other hydraulic systems. They help absorb pressure fluctuations, protecting system components from excessive stress and premature wear. At the same time, they contribute to stable and efficient system operation by reducing sudden pressure variations.

The AQUASTRONG ECMI(m)2-3SE is an Intelligent stainless steel multistage centrifugal surface pump designed for pressure boosting, household water supply and automatic irrigation applications. Its integrated PCL microcomputer chip provides automatic control of pump operation, offering a practical solution for water supply systems where automatic operation and additional protection are required. The Intelligent control system provides automatic start and stop, delay-start protection and no-water protection, helping protect the pump and ensuring reliable operation according to water demand. Powered by a 0.37kW (0.5HP) single-phase motor, the pump delivers a maximum flow rate of 4.5 m³/h (75 L/min) and a maximum head of 27 m. Its multistage hydraulic design provides consistent pressure across a wide operating range. The motor features copper windings, built-in thermal protection, Class F insulation and IPX4 protection. The pump is suitable for clean water or liquids with similar physical and chemical properties, with an operating liquid temperature range of 4–60°C, a maximum ambient temperature of 50°C, and a maximum working pressure of 10 bar.   Comes with a 1.6 m power cable with UK plug.

The IMAS IM25-6-180 is a three-speed hot water circulator pump designed for circulating clean water and liquids that do not contain chemicals. It is suitable for domestic heating and air-conditioning systems operating under pressure in closed or open circuits. The pump features three selectable operating speeds, with power consumption of 46W, 67W and 93W, allowing its performance to be adjusted according to the requirements of the installation. It provides a maximum flow rate of 4.1 m³/h and a maximum head of 6 m. The hydraulic section is manufactured from cast iron and incorporates a wet-rotor motor. The motor housing is made of die-cast aluminium, while the impeller is manufactured from technopolymer. The hardened stainless steel motor shaft is supported by graphite bearings and lubricated directly by the pumped liquid. The rotor protective casing, stator casing and sealing flange are manufactured from stainless steel. The pump also features a ceramic thrust ring, ethylene-propylene sealing rings and a brass air vent plug. Designed for hot-water circulation, the IM25-6-180 can handle liquid temperatures up to 110°C and a maximum operating pressure of 10 bar. It operates from a single-phase 230V/50Hz power supply and features IP44 protection and Class F insulation. The pump has an installation length of 180 mm, 1½" threaded connections and must be installed with the motor shaft in a horizontal position.